Your Disc Didn't Get Slower. It Got Smaller.

2026-11-06 11:00

W12_可用直径_16x9.jpgThere is a complaint that arrives with the same words in every abrasive business. The disc cut well for a while, and then it went soft. The conclusion at the counter is that the grit was tired, or the batch was different, or the supplier changed something.

Measure the disc. It is smaller. That is the whole of it.

Thickness gets argued about at the quotation, because thickness is on the drawing and someone has to sign for it. Diameter changes on its own, with nobody deciding anything, and it is the dimension that decides what the disc can still do.

Rim speed is pi times diameter times revolutions, divided by sixty. On one machine, at one speed setting, the only term that can move is the diameter. So the speed at the edge is a straight ratio of the diameter, and it has been falling since the first cut.

Twenty millimetres off the radius takes a 115 down to 75. Three quarters of the diameter, three quarters of the speed. The same twenty millimetres takes a 230 down to 190, which is 83 per cent. Identical wear, and the small disc has given up twice as much of its speed.

What that does to the cut rate, nobody should claim from arithmetic alone. But the bond, the grit and the reinforcement were selected against a speed. A disc is a system balanced at one working speed, and when the speed moves, something in that balance has to give.

The second thing the diameter sets

The deepest cut a disc can make in a single pass is its radius, because the rim cannot pass lower than one radius below the spindle it turns on. A new 107 reaches 53.5 millimetres. A 115, 57.5. A 125, 62.5. A 180, 90. A 230, 115. A guard, the clamping nut and the approach angle all take something off those figures, but the ceilings are real, and they only fall.

So a 115 worn to 75 reaches 37.5 millimetres. The fifty millimetre bar it was bought for is not slow now. It is out of range.

Two limits that fail at different moments

Put the two side by side. The disc is finished when it can no longer reach the cut, which happens at a diameter twice the cut depth. And it is finished when it is too slow to be worth running, which happens at some fraction of the diameter it started with. I will use eighty per cent for this arithmetic. That is a convention, not a specification, and the next paragraph shows what happens when it moves.

One limit is a fixed depth. The other is a fixed fraction. They cross at a diameter of two and a half times the cut depth. Below that crossing, the job outgrows the disc. Above it, the disc goes slow while it still has reach in hand.

For a fifty millimetre cut the crossing lands at 125 millimetres. On that job a 107 and a 115 run out of reach before they run out of speed, and a 180 and a 230 run out of speed long before they run out of reach. The 125 sits on the line, and which side of it the 125 lands on depends on the threshold: ninety per cent puts the crossing near 111, seventy per cent near 143. The 107 is reach-limited under all of them. The 180 and the 230 are speed-limited under all of them. Nothing in the conclusion depends on the number I picked.

So when a disc is finished has no single answer. On a fifty millimetre cut, a 107 can lose seven millimetres of diameter, six and a half per cent, before the job is past it. A 115 can lose fifteen, thirteen per cent. From 125 upward the speed limit is the only one that bites, and the answer is the same twenty per cent for every size in the catalogue.

The correction that makes it true

The operator feels the drop. A hand notices eighty per cent speed long before any instrument would, and the instinct at that point is to lean.

Leaning adds force. It does not add rim speed. What it adds is pressure along the same length of edge, which raises the temperature where the work is being done, and heat is what closes a bond, glazes the grit and ends self-sharpening. The disc that was merely slow becomes a disc that is genuinely dead.

That is the only place in this argument where the shop's diagnosis comes true, and it comes true because the diagnosis was acted on.

The flip is not free either

The usual workaround is to turn the part and cut from the other side. It works, and it should be counted at its real price. The travel doubles. Two faces have to meet, and they meet worse than one face would have, because the second pass starts from a surface that has already moved and on an edge that is no longer square to the first. On a part with a tolerance, that is the difference between a cut and a repair.

"The disc still does the job" is true only if the job has been redefined as two passes. Redefining the job is a legitimate decision. Not noticing that you made it is not.

Where the change point goes

Take the depth of your cut and double it. That is the smallest diameter that can still reach. Take the largest disc you would buy for the same job and decide what fraction of its speed you are willing to give up. Whichever number is larger is where the disc is finished, and it can be written on the machine before the disc says anything at all.

Run it once per job and the argument about whether the abrasive has gone off stops happening, because the disc gets changed while it is still a disc.

And one thing said plainly

This article argues for changing discs earlier, which means selling more of them. It also means the cut on the bench is the cut the disc was designed to make. Both of those are worth having, and only one of them is a coincidence.

A disc is not finished when the abrasive is gone. It is finished when it can no longer do the job it was bought for, and on a small disc that moment arrives a long time before the abrasive does.

Tel:+86 519 83122289
WhatsApp:+86 13775130532
Email:wangyi@vexaabrasives.com